A Quick Guide to Welding and Weld Inspection

Herausgegeben:Hughes, S E

Leseprobe

A Quick Guide to Welding and Weld Inspection

Leseprobe

Fotogalerie

A Quick Guide to Welding and Weld Inspection

Herausgegeben:Hughes, S E

Broschiertes Buch

Jetzt bewerten Jetzt bewerten

A concise and accessible guide to the knowledge required to fulfil the role of a welding inspector. In covering both European and US-based codes, the book gives those wishing to gain certification in welding inspection a basic all-round understanding of the main subject matter.

Andere Kunden interessierten sich auch für

J Norrish
Advanced Welding Processes

147,99 €
Welding and Joining of Aerospace Materials

183,99 €
Welding and Joining of Aerospace Materials

162,99 €
Reza Amini Najafabadi
Effect Of The Electrode Shape On Weld Pool Parameters Of Carbon Steel

36,99 €
M.-K. Besharati-Givi
Advances in Friction-Stir Welding and Processing

113,99 €
G Mathers
The Welding of Aluminium and Its Alloys

143,99 €
H. Granjon
Fundamentals of Welding Metallurgy

140,99 €

Produktbeschreibung

Produktdetails

Produktdetails
Woodhead Publishing Series in Welding and Other Joining Technologies
Verlag: Elsevier Science & Technology / Woodhead Publishing
Artikelnr. des Verlages: C2013-0-17302-3
Englisch
Abmessung: 7mm x 105mm x 171mm
Gewicht: 140g
ISBN-13: 9781845696412
Artikelnr.: 40427150

Herstellerkennzeichnung

Produktdetails

Woodhead Publishing Series in Welding and Other Joining Technologies
Verlag: Elsevier Science & Technology / Woodhead Publishing
Artikelnr. des Verlages: C2013-0-17302-3
Englisch
Abmessung: 7mm x 105mm x 171mm
Gewicht: 140g
ISBN-13: 9781845696412
Artikelnr.: 40427150

Herstellerkennzeichnung

Inhaltsangabe

Foreword by Series Editor
Introduction
A 10 Minute Guide
- 1 What is the difference between the main welding processes? (four minutes)
- 2 Why use welding symbols? (one minute)
- 3 What are codes and standards? (one minute)
- 4 What is welding procedure qualification? (one minute)
- 5 Why does a welder need qualification? (one minute)
- 6 What are welding defects? (two minutes)
Chapter 1: Abbreviations, Terminology and Welding Symbols
- Abbreviations
- Common terms
- Joint terminology
- Weld terminology
- Drawing rules and weld symbols
Chapter 2: Duties of a Welding Inspector
- Before welding
- During welding
- After welding
- Repairs
Chapter 3: Analysis of a Fusion Weld
- Components of a welded joint
- What makes a good fusion weld?
- Weld joint: preparation methods
- Weld joint: shape
- Residual stress and distortion
- Minimising stresses and distortion
Chapter 4: Materials and Their Weldability
- Carbon equivalency
- Classification of steels
- Alloying elements
- Material properties
- Heat treatment of steels
Chapter 5: Welding Processes
- Manual metal arc (MMA)/shielded metal arc welding (SMAW)
- Metal inert gas (MIG)/metal active gas (MAG)/gas metal arc welding (GMAW)
- Flux-cored arc welding (FCAW)
- Tungsten inert gas (TIG)/gas tungsten arc welding (GTAW)
- Submerged arc welding (SAW)
Chapter 6: Non-destructive and Destructive Testing
- Liquid penetrant testing (PT)
- Magnetic particle testing (MT)
- Ultrasonic testing (UT)
- Radiographic testing (RT)
- Tension tests
- Bend tests
- Charpy tests
- Hardness testing
- Macro samples
- Micro samples
- Fillet fracture test
- Butt weld fracture test (nick break)
Chapter 7: Fracture Modes and Welding Defects
- Imperfection categories
- Hydrogen-induced cold cracking (HICC)
- Solidification cracking
- Reheat cracking
- Lamellar tearing
- Weld decay
- Porosity
- Solid inclusions
- Lack of fusion
- Incomplete root penetration
- Root concavity
- Excessive root penetration
- Overlap
- Underfill
- Undercut
- Crater pipe
- Burn-through
- Root oxidation
- Arc strike
- Spatter
- Magnetic arc blow
Chapter 8: Codes, Standards and Documentation
- Codes and standards
- The PED and UK PER
- Welding procedure qualifications
- Procedure qualification record (PQR)
- Welding procedure specification (WPS)
- Welder qualifications
Chapter 9: Health and Safety
- Health and Safety at Work Act
- Electrical safety
- Welding/cutting process safety
- Personal protective equipment (PPE)
- Gases and fumes
- COSHH and workplace exposure limits (WEL)
- Lifting equipment/pressure system requirements
- Hand tools and grinding machines
- Other precautions before welding starts
- Causes of accidents
- Permit-to-work
- Tanks and drums
Index

Inhaltsangabe

Foreword by Series Editor
Introduction
A 10 Minute Guide
- 1 What is the difference between the main welding processes? (four minutes)
- 2 Why use welding symbols? (one minute)
- 3 What are codes and standards? (one minute)
- 4 What is welding procedure qualification? (one minute)
- 5 Why does a welder need qualification? (one minute)
- 6 What are welding defects? (two minutes)
Chapter 1: Abbreviations, Terminology and Welding Symbols
- Abbreviations
- Common terms
- Joint terminology
- Weld terminology
- Drawing rules and weld symbols
Chapter 2: Duties of a Welding Inspector
- Before welding
- During welding
- After welding
- Repairs
Chapter 3: Analysis of a Fusion Weld
- Components of a welded joint
- What makes a good fusion weld?
- Weld joint: preparation methods
- Weld joint: shape
- Residual stress and distortion
- Minimising stresses and distortion
Chapter 4: Materials and Their Weldability
- Carbon equivalency
- Classification of steels
- Alloying elements
- Material properties
- Heat treatment of steels
Chapter 5: Welding Processes
- Manual metal arc (MMA)/shielded metal arc welding (SMAW)
- Metal inert gas (MIG)/metal active gas (MAG)/gas metal arc welding (GMAW)
- Flux-cored arc welding (FCAW)
- Tungsten inert gas (TIG)/gas tungsten arc welding (GTAW)
- Submerged arc welding (SAW)
Chapter 6: Non-destructive and Destructive Testing
- Liquid penetrant testing (PT)
- Magnetic particle testing (MT)
- Ultrasonic testing (UT)
- Radiographic testing (RT)
- Tension tests
- Bend tests
- Charpy tests
- Hardness testing
- Macro samples
- Micro samples
- Fillet fracture test
- Butt weld fracture test (nick break)
Chapter 7: Fracture Modes and Welding Defects
- Imperfection categories
- Hydrogen-induced cold cracking (HICC)
- Solidification cracking
- Reheat cracking
- Lamellar tearing
- Weld decay
- Porosity
- Solid inclusions
- Lack of fusion
- Incomplete root penetration
- Root concavity
- Excessive root penetration
- Overlap
- Underfill
- Undercut
- Crater pipe
- Burn-through
- Root oxidation
- Arc strike
- Spatter
- Magnetic arc blow
Chapter 8: Codes, Standards and Documentation
- Codes and standards
- The PED and UK PER
- Welding procedure qualifications
- Procedure qualification record (PQR)
- Welding procedure specification (WPS)
- Welder qualifications
Chapter 9: Health and Safety
- Health and Safety at Work Act
- Electrical safety
- Welding/cutting process safety
- Personal protective equipment (PPE)
- Gases and fumes
- COSHH and workplace exposure limits (WEL)
- Lifting equipment/pressure system requirements
- Hand tools and grinding machines
- Other precautions before welding starts
- Causes of accidents
- Permit-to-work
- Tanks and drums
Index