Control Methods for Electrical Machines (eBook, ePUB)

Redaktion: Husson, Rene

• Format: ePub

Produktbeschreibung

The type of control system used for electrical machines depends on the use (nature of the load, operating states, etc.) to which the machine will be put. The precise type of use determines the control laws which apply. Mechanics are also very important, because they affect performance. Another factor of essential importance in industrial applications is operating safety. Finally, the problem of how to control a number of different machines, whose interactions and outputs must be coordinated, is addressed and solutions are presented. These and other issues are addressed here by a range of expert contributors, each of whom are specialists in their particular field. This book is primarily aimed at those involved in complex systems design, but engineers in a range of related fields such as electrical engineering, instrumentation and control, and industrial engineering, will also find this a useful source of information.

---

Dieser Download kann aus rechtlichen Gründen nur mit Rechnungsadresse in A, B, BG, CY, CZ, D, DK, EW, E, FIN, F, GR, HR, H, IRL, I, LT, L, LR, M, NL, PL, P, R, S, SLO, SK ausgeliefert werden.

Produktdetails

• Verlag: John Wiley & Sons
• Seitenzahl: 384
• Erscheinungstermin: 1. März 2013
• Englisch
• ISBN-13: 9781118617472
• Artikelnr.: 38247655

Autorenporträt

René Husson is an Emeritus Professor at INPL (ENSEM), Nancy, France.

Inhaltsangabe

Preface xi
Chapter 1. Overview of Mechanical Transmission Problems 1
Pascal FONTAINE and Christian CUNAT
1.1. Technological aspects1
1.2. Bibliography 28
Chapter 2. Reminders of Solid Mechanics 31
Jean-Francois SCHMITT and Rachid RAHOUADJ
2.1. Reminders of dynamics 31
2.2. Application example: dynamic balance of a rigid rotor 42
2.3. Analytical dynamics (Euler-Lagrange) 46
2.4. Linear energies in the neighborhood of the balance for a non-damped
discrete system 49
2.5. Vibratory behavior of a discrete non-damped system around an
equilibrium configuration 51
2.6. Analytical study of the vibratory behavior of a milling machine table
53
2.7. Bibliography 61
Chapter 3. Towards a Global Formulation of the Problem of Mechanical Drive
63
Christian CUNAT, Mohamed HABOUSSI and Jean Francois GANGHOFFER
3.1. Presentation of the mechanical drive modeling problem 63
3.2. Brief review on continuum mechanics 72
3.3. Bibliography 89
Chapter 4. Continuous-time Linear Control 91
Frederic KRATZ
4.1. Introduction 91
4.2. PID controllers 91
4.3. PID controllers 100
4.4. Methods based on previous knowledge of a system model 104
4.5. Linear state feedback control systems 107
4.6. Optimal control 117
4.7. Choice of a control 129
4.8. Bibliography 130
Chapter 5. Overview of Various Controls 131
Frederic KRATZ
5.1. Introduction 131
5.2. Internal model controller 132
5.3. Predictive control 141
5.4. Sliding control 149
5.5. Bang-bang control 152
5.6. Control-based fuzzy logic 154
5.7. Neural network control 164
5.8. Bibliography 167
Chapter 6. Sliding Mode Control 169
Rachid OUTBIB and Michel ZASADZINSKI
6.1. Introduction169
6.2. Illustrative example 170
6.3. Basic concepts 172
6.4. Direct Lyapunov method 184
6.5. Equivalent control method 189
6.6. Imposing a surface dynamic 198
6.7. The choice of sliding surface 200
6.8. Conclusion 203
6.9. Notations 203
6.10. Bibliography 204
Chapter 7. Parameter Estimation for Knowledge and Diagnosis of Electrical
Machines 207
Jean-Claude TRIGEASSOU, Thierry POINOT and Smail BACHIR
7.1. Introduction 207
7.2. Identification using output-error algorithms 210
7.3. Parameter estimation with a priori information 218
7.4. Parameter estimation of the induced machine 225
7.5. Fault detection and localization based on parameter estimation 232
7.6. Conclusion 241
7.7. Bibliography 241
Chapter 8. Diagnosis of Induction Machines by Parameter Estimation 245
Smail BACHIR, Slim TNANI, Gerard CHAMPENOIS and Jean-Claude TRIGEASSOU
8.1. Introduction 245
8.2. Induction motor model for fault detection 246
8.3. Diagnosis procedure 261
8.4. Conclusion 267
8.5. Bibliography 268
Chapter 9. Time-based Coordination 271
Michel DUFAUT and Rene HUSSON
9.1. Introduction 271
9.2. Brief description system 272
9.3. Some ideas on the manipulator system models 277
9.4. Coordination of motion 286
9.5. Conclusion 304
9.6. Bibliography 304
Chapter 10. Multileaf Collimators 307
Sabine ELLES and Bruno MAURY
10.1. Radiotherapy 307
10.2. Multileaf collimators 310
10.3. Intensity modulated radiotherapy 317
10.4. Conclusion 328
10.5. Bibliography 329
Chapter 11. Position and Velocity Coordination: Control of Machine-Tool
Servomotors 331
Patrick BOUCHER and Didier DUMUR
11.1. Open architecture systems 331
11.2. Structure and implementation of control laws 334
11.3. Application to machines-tools axis drive control 339
11.4. Conclusions 362
11.5. Bibliography 364
List of Authors 367
Index 369